% LAY_e2.TEX - Anhang von LAYOUT.TEX (PA 1988) %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% \clearpage \section*{Appendix} \addcontentsline{toc}{section}{Appendix} \appendix \section{The page structure in \LaTeX} This appendix describes how the actual page is build from its components and how they are influenced by \TeX{}'s parameters. (\seealso{Fig.\,\ref{bild}} Figure~\ref{bild} has been created by Nelson Beebe at the University of Utah.) \begin{description} \item[text area] The normal text area (``Body'') contains the running text including footnotes, tables and figures. The headings, footer and margin notes do \emph{not} belong to the text area. The text area has the width \cs{textwidth} and the height \cs{text\-height}. In a two column layout the text area is split into two columns, with the width \cs{columnwidth} each and a space of \cs{columnsep} between them. Thus the \cs{columnwidth} is a little bit smaller than half the \cs{textwidth}. \cs{textwidth} and \cs{columnwidth} should be a multiple of the width of one character in the \texttt{tt} font. \cs{textheight} should be multiple of the line height \cs{baselineskip}, increased by the constant value of \cs{topskip}. Indentations inside the text area are defined with \cs{leftskip} and \cs{rightskip}. These parameters should not be changed explicitly by the user but rather implicitly through environments. \item[left margin] The left margin is either \cs{odd-} or \cs{evensidemargin} plus 1~inch. Both parameters have the same value, unless the \texttt{twoside} option is given. \item[top margin] The top margin is the sum of \cs{topmargin}, \cs{headheight} and \cs{headsep} plus 1~inch. \item[right margin] The right margin is the paper width minus the left margin and the text area. \item[bottom margin] The bottom margin is the paper height minus the top margin and the text area. \item[heading]\index{headings} The heading is inside the top margin with a space of \cs{headsep} between the lower border of the header and the upper border of the text area. Above the header is a free space of \cs{topmargin} increased by 1~inch. \item[footing]\index{footings} The footer is inside the bottom margin with a space of \cs{footskip} between the lower border of the text area and the lower border of the footer. \item[margin notes]\index{margin notes} Margin notes are inside the left or right margin. They have a width of \cs{marginparwidth} and a space of \cs{marginparsep} between the margin note and the text area. The vertical space between two margin notes is \cs{marginparpush}. \end{description} The \texttt{paperheight} consists of the following elements (from top to bottom): \begin{verse} 1 inch \\*[2pt] \cs{topmargin} \\*[2pt] \cs{headheight} \\*[2pt] \cs{headsep} \\*[2pt] \cs{textheight} \\*[2pt] \cs{footskip} \\*[2pt] remaining page. \end{verse} On pages with margin notes in the right margin the \texttt{paperwidth} consists of the following elements: \begin{verse} 1 inch\\*[2pt] \cs{oddsidemargin} \ \ or\ \ \cs{evensidemargin}\\*[2pt] \cs{textwidth}\\*[2pt] \cs{marginparsep}\\*[2pt] \cs{marginparwidth}\\*[2pt] remaining page \end{verse} With the option \texttt{twoside} the left pages change to \begin{verse} 1 inch\\*[2pt] \cs{evensidemargin}\\*[2pt] \cs{textwidth}\\*[2pt] remaining page \end{verse} \marginlabel{Comments:} The parameters \cs{topmargin}, \cs{oddsidemargin}, and \cs{evensidemargin} may be negative. In this case, the margin will be smaller than 1~inch. The same is true for \cs{leftskip} and \cs{rightskip} which leads to text that is wider than the text area. Extensive treatment and figures to this subject may be found in the \textsc{TUGboat} Vol.9, No.1 (April 1988). The parameter \cs{footheight} is no longer defined in \LaTeXe\ since no-one used it. %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% \begin{fullpage} %%%%%%%%%%%%%%%% % Bild von Nelson Beebe, mit geringen "Anderungen von PA: \newcommand{\X}[1]{{#1}\index{{#1}}} % NB: For computed dimension parameters, we cannot use % \newcommand{}, because this expands to a TeX \def which does % not evaluate the definition before assigning it to the control % sequence name; we use \xdef directly to force evaluation \newcount\T % temporary counter for arithmetic calculations \T=0 % ********************************************************************** % WARNING: Do not insert ANY aditional whitespace in these % macros--otherwise it ends up in the TeX boxes and ruins the % positioning, sigh.... % ********************************************************************** % NAMEBOX{x}{y}{dx}{dy}{width}{height}{pos}{label} -- framed label with % box lower-left corner at (x+dx,y+dy) \newcommand{\NAMEBOX}[8]{\put(#1,#2){\begin{picture}(0,0)(-#3,-#4)\ignorespaces \framebox(#5,#6)[#7]{#8}\end{picture}}} % HARROW{x}{y}{dx}{dy}{length}{side}{pos}{label} -- horizontal % labeled arrow with left point at (x+dx,y+dy), label on bottom % (side=b) or top (side=t) of arrow, in makebox[pos] \newcommand{\HARROW}[8]{\put(#1,#2){\begin{picture}(0,0)(-#3,-#4)\ignorespaces \put(0,0){\vector(1,0){#5}}\ignorespaces \put(#5,0){\vector(-1,0){#5}}\ignorespaces \ifthenelse{\equal{#6}{b}}{\ignorespaces \put(0,-\TAD){\makebox(#5,0)[#7]{#8}} }{\ignorespaces \ifthenelse{\equal{#6}{t}}{}{\ignorespaces \typeout{Side #6 must be ``b'' or ``t''--``t'' assumed}}\ignorespaces \put(0,\TAD){\makebox(#5,0)[#7]{#8}} } \end{picture}}} % VARROW{x}{y}{dx}{dy}{length}{side}{pos}{label} -- vertical % labeled arrow with left point at (x+dx,y+dy), label on left % (side=l) or right (side=r) of arrow, in makebox[pos] \newcommand{\VARROW}[8]{\put(#1,#2){\begin{picture}(0,0)(-#3,-#4)\ignorespaces \put(0,0){\vector(0,1){#5}}\ignorespaces \put(0,#5){\vector(0,-1){#5}}\ignorespaces \ifthenelse{\equal{#6}{l}}{\ignorespaces \put(-\TAD,0){\makebox(0,#5)[#7]{#8}} }{\ignorespaces \ifthenelse{\equal{#6}{r}}{}{\ignorespaces \typeout{Side #6 must be ``r'' or ``l''--``r'' assumed}}\ignorespaces \put(\TAD,0){\makebox(0,#5)[#7]{#8}} } \end{picture}}} % VRULE{x}{y}{dx}{dy}{length}{side}{pos}{label} -- vertical % rule with left point at (x+dx,y+dy), label on left % (side=l) or right (side=r) of rule, in makebox[pos] \newcommand{\VRULE}[8]{\put(#1,#2){\begin{picture}(0,0)(-#3,-#4)\ignorespaces \put(0,0){\line(0,1){#5}}\ignorespaces \ifthenelse{\equal{#6}{l}}{\ignorespaces \put(0,0){\makebox(0,#5)[#7]{$\rightarrow${}#8}} }{\ignorespaces \ifthenelse{\equal{#6}{r}}{}{\ignorespaces \typeout{Side #6 must be ``r'' or ``l''--``r'' assumed}}\ignorespaces \put(0,0){\makebox(0,#5)[#7]{$\leftarrow${}#8}} } \end{picture}}} % ********************************************************************** % If you wish to change any of these values: % * definitions are mostly in alphabetical order % * remember units are in centipoints for accurate % positioning % * most parameters are taken directly from values in % BK11.STY, but in order to improve the appearance of the % figure, a few have been increased to avoid overlap of % labels and/or boxes, or to loosen up the figure % * ALL parameters which depend on others are defined by % computation and \xdef's below; they must NEVER be % changed % %- For 11pt BOOK style, \textwidth / \pagewidth(8.5in) = 0.5294 %- Anything larger than this will generate an overfull box. We %- choose 0.50 since that makes scaling trivial for the reader %- \newcommand{\UNITLENGTH}{0.005pt} %- \newcommand{\SCALEFACTOR}{50\%} % %-----> We use a larger picture with 0.70 on our DIN-A4 paper: \newcommand{\UNITLENGTH}{0.007pt} \newcommand{\SCALEFACTOR}{70\%} % <------------------------------ % % US papersize... % \newcommand{\PAGEHEIGHT}{79497} % 11in in centipoints \newcommand{\PAGEWIDTH}{61430} % 8.5in in centipoints % % Typical dimensions from BK10.DOC % \newcommand{\BASELINESKIP}{2000} % really 1000, but this is % too tight for the figure \newcommand{\COLUMNSEP}{1000} \newcommand{\COLUMNSEPRULE}{0} % DVI drivers put top left corner at (1in,1in) from physical page % left corner \newcommand{\DVIXOFFSET}{7227} \newcommand{\DVIYOFFSET}{7227} \newcommand{\EVENSIDEMARGIN}{10841} \newcommand{\FOOTHEIGHT}{2400} % really 1200, but too tight \newcommand{\FOOTNOTESEP}{665} \newcommand{\FOOTSKIP}{4207} % really 2529, but too tight; for symmetry, % make FOOTSKIP=HEADSEP+FOOTHEIGHT \newcommand{\HEAdHEIGHT}{2400} % really 1200, but too tight \newcommand{\HEADSEP}{1807} \newcommand{\MARGINPARPUSH}{2000} % really 500, but too tight \newcommand{\MARGINPARSEP}{2800} % really 700, but too tight \newcommand{\MARGINPARWIDTH}{7227} \newcommand{\MARGINNOTEHEIGHT}{4444} % arbitrary value (holds % ``Margin Note A'' on % 2 lines) \newcommand{\ODDSIDEMARGIN}{3613} % % Upper left page corner (0,0) is at (1in,1in) on physical page % for DVI drivers. Position the LOWER left corner at % (\PAGEXORIGIN,\PAGEYORIGIN), where \PAGEYORIGIN is computed % below \newcommand{\PAGEXORIGIN}{\DVIXOFFSET} \newcommand{\TAD}{800} % how far to move labels from their arrows \newcommand{\TEXTHEIGHT}{50400} \newcommand{\TEXTWIDTH}{32522} \newcommand{\TOPMARGIN}{5420} % ********************************************************************** % DO NOT CHANGE any of these computed parameters % % \T=\TEXTWIDTH \advance\T by -\COLUMNSEP \divide\T by 2 \xdef\COLUMNWIDTH{\the\T} \T=\TEXTWIDTH \divide\T by 2 \advance\T by \ODDSIDEMARGIN \xdef\COLUMNXMIDDLE{\the\T} % 0.5*TEXTWIDTH+ODDSIDEMARGIN \T=\COLUMNWIDTH \advance\T by \ODDSIDEMARGIN \advance\T by \COLUMNSEP \xdef\COLUMNTWOX{\the\T} % COLUMNWIDTH+COLUMNSEP+ODDSIDEMARGIN \T=\FOOTSKIP \advance\T by \TEXTHEIGHT \advance\T by \HEADSEP \xdef\HEADYORIGIN{\the\T} % FOOTSKIP+TEXTHEIGHT+HEADSEP % % Inner TeX page dimensions are (\INNERWIDTH,\INNERHEIGHT). All TeX % coordinates are relative to (0,0) at upper-left corner of this % page, although for the figures, we put (0,0) at lower-left % corner. % \T=\TOPMARGIN \advance\T by \HEAdHEIGHT \advance\T by \HEADSEP \advance\T by \TEXTHEIGHT \advance\T by \FOOTSKIP % INNERHEIGHT=TOPMARGIN+HEAdHEIGHT+HEADSEP+TEXTHEIGHT+FOOTSKIP \xdef\INNERHEIGHT{\the\T} \T=\ODDSIDEMARGIN \advance\T by \TEXTWIDTH \advance\T by \EVENSIDEMARGIN \xdef\INNERWIDTH{\the\T} % ODDSIDEMARGIN+TEXTWIDTH+EVENSIDEMARGIN \T=\ODDSIDEMARGIN \advance\T by \TEXTWIDTH \advance\T by \MARGINPARSEP \xdef\MARGINNOTEXORIGIN{\the\T} % ODDSIDEMARGIN+TEXTWIDTH+MARGINPARSEP \T=\TEXTHEIGHT \multiply\T by 75 \divide\T by 100 \advance\T by \FOOTSKIP \xdef\MARGINNOTEYA{\the\T} % .75*TEXTHEIGHT+FOOTSKIP \T=\MARGINNOTEYA \advance\T by -\MARGINNOTEHEIGHT \advance\T by -\MARGINPARPUSH \xdef\MARGINNOTEYB{\the\T} % MARGINNOTEYA-MARGINNOTEHEIGHT-MARGINPARPUSH \T=\MARGINNOTEYA \advance\T by \MARGINNOTEHEIGHT \xdef\MARGINNOTEYC{\the\T} % MARGINNOTEYA+MARGINNOTEHEIGHT \T=\PAGEHEIGHT \advance\T by -\DVIYOFFSET \xdef\PAGEYTOP{\the\T} % PAGEHEIGHT-DVIYOFFSET \T=\PAGEYTOP \advance\T by -\INNERHEIGHT \xdef\PAGEYORIGIN{\the\T} % PAGEYTOP-INNERHEIGHT \T=\ODDSIDEMARGIN \advance\T by \TEXTWIDTH \xdef\RIGHTEDGE{\the\T} % ODDSIDEMARGIN+TEXTWIDTH \T=\TEXTHEIGHT \multiply\T by 4 \divide\T by 10 \xdef\TEXTY{\the\T} % TEXTY = 0.4*TEXTHEIGHT (we put % sample text here) \T=\TEXTHEIGHT \divide\T by 3 \xdef\TEXTWIDTHY{\the\T} % TEXTWIDTHY = TEXTHEIGHT/3 (we % put \textwidth label here) \begin{figure} %%%%%%%%%%%%%% \caption{Page layout} \label{bild} \begin{center} \begin{small} % make text somewhat smaller \setlength{\unitlength}{\UNITLENGTH} \begin{picture}(\PAGEWIDTH,\PAGEHEIGHT) % sizes in centipoints % \NAMEBOX{0}{0}{0}{0}{\PAGEWIDTH}{\PAGEHEIGHT}{}{} % \HARROW{0}{\PAGEYTOP}{0}{0}{\PAGEXORIGIN}{b}{}{1in} % \VARROW{\PAGEXORIGIN}{\PAGEYTOP}{0}{0}{\DVIYOFFSET}{r}{l}{1in} % \put(\PAGEXORIGIN,\PAGEYORIGIN){ \begin{picture}(\INNERWIDTH,\INNERHEIGHT) % Draw 3-sided inner page frame--no bottom side % because it is not significant for dimensioning \put(0,0){\line(0,1){\INNERHEIGHT}} \put(0,\INNERHEIGHT){\line(1,0){\INNERWIDTH}} \put(\INNERWIDTH,0){\line(0,1){\INNERHEIGHT}} % \NAMEBOX{\ODDSIDEMARGIN}{\TEXTY}{0}{0}{\TEXTWIDTH}{ \BASELINESKIP}{l}{A line of text\ldots} \NAMEBOX{\ODDSIDEMARGIN}{\TEXTY}{0}{-\BASELINESKIP}{ \TEXTWIDTH}{\BASELINESKIP}{l}{Next line\ldots} % \VARROW{\COLUMNXMIDDLE}{\TEXTY}{0}{-\BASELINESKIP}{ \BASELINESKIP}{r}{l}{\tt\string\baselinestretch $\times$\string\baselineskip} % \HARROW{0}{\TEXTHEIGHT}{0}{0}{\ODDSIDEMARGIN}{t}{}{ \tt\string\oddsidemargin} \HARROW{0}{\TEXTHEIGHT}{0}{0}{\ODDSIDEMARGIN}{b}{}{ \tt\string\evensidemargin} % % Page text label \NAMEBOX{\ODDSIDEMARGIN}{\FOOTSKIP}{0}{0}{\TEXTWIDTH}{ \TEXTHEIGHT}{}{Page Text} % Page footer box, arrow, and label \NAMEBOX{\ODDSIDEMARGIN}{0}{0}{0}{\TEXTWIDTH}{ \FOOTHEIGHT}{}{Page Footer} % \VARROW{\ODDSIDEMARGIN}{0}{-\TAD}{0}{\FOOTHEIGHT}{l}{r}{ \tt\string\footheight} % % Footskip arrow and label \VARROW{\RIGHTEDGE}{0}{\TAD}{0}{\FOOTSKIP}{r}{l}{ \tt\string\footskip} % \HARROW{\ODDSIDEMARGIN}{\TEXTWIDTHY}{0}{0}{\TEXTWIDTH}{b}{}{ \tt\string\textwidth} % \VARROW{\ODDSIDEMARGIN}{\FOOTSKIP}{-\TAD}{0}{ \TEXTHEIGHT}{l}{r}{\tt\string\textheight$\rightarrow$} % \VARROW{\ODDSIDEMARGIN}{\HEADYORIGIN}{-\TAD}{0}{ \HEAdHEIGHT}{l}{r}{\tt\string\headheight} % \VARROW{\RIGHTEDGE}{\HEADYORIGIN}{\TAD}{-\HEADSEP}{ \HEADSEP}{r}{l}{\tt\string\headsep} % \VARROW{\RIGHTEDGE}{\INNERHEIGHT}{\TAD}{-\TOPMARGIN}{ \TOPMARGIN}{r}{l}{\tt\string\topmargin} % \NAMEBOX{\ODDSIDEMARGIN}{\HEADYORIGIN}{0}{0}{\TEXTWIDTH}{ \HEAdHEIGHT}{}{Page Header} % \NAMEBOX{\MARGINNOTEXORIGIN}{\MARGINNOTEYA}{0}{0}{ \MARGINPARWIDTH}{\MARGINNOTEHEIGHT}{}{\shortstack{ Margin\\note A}} % \VARROW{\MARGINNOTEXORIGIN}{\MARGINNOTEYA}{-\TAD}{ -\MARGINPARPUSH}{\MARGINPARPUSH}{l}{r}{ \tt\string\marginparpush} % \NAMEBOX{\MARGINNOTEXORIGIN}{\MARGINNOTEYB}{0}{0}{ \MARGINPARWIDTH}{\MARGINNOTEHEIGHT}{}{\shortstack{Margin\\note B}} % \HARROW{\MARGINNOTEXORIGIN}{\MARGINNOTEYB}{0}{-\TAD}{ \MARGINPARWIDTH}{b}{}{\tt\string\marginparwidth} % \HARROW{\MARGINNOTEXORIGIN}{\MARGINNOTEYC}{ -\MARGINPARSEP}{\TAD}{\MARGINPARSEP}{t}{}{ \tt\string\marginparsep} % \end{picture}} \end{picture} \end{small} \end{center} \end{figure} %%%%%%%%%%%% \clearpage %%%%%%%%%% \end{fullpage} %%%%%%%%%%%%%% %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% \section{Description of the refman-class family} \label{refman} The \texttt{refman.sty} was defined at the EDV-Zentrum (computing center) of the TU\footnote{Technical University} Wien. This layout is suitable for reference manuals, technical descriptions and similar applications. It is based on the ideas shown in previous sections: The layout has a wide left margin for headings and margin notes and smaller margins on the right side, the top and the bottom. In 1994 this layout was re-implemented as a class for the new \LaTeXe. This made it possible to include some minor improvements, such as the support of different paper sizes. The \texttt{refman.sty} was split into two classes \texttt{refrep}\index{refrep.cls}, similar to \texttt{report} and \texttt{refart}\index{refart.cls}, similar to \texttt{article}. These classes differ in the layout of the header and footer. The \texttt{refart} does not support the \cs{chapter} command. The current version of both classes is described in this document. It serves as an example for the layout. \subsection{Invocation} \index{refart, invocation} \index{refrep, invocation} The \LaTeX\ local guide (if available) shows if this class is available at your \TeX\ installation or where to install it. To use the \texttt{refart} class, simply call it with the \cs{documentclass} command: \begin{verbatim} \documentclass[11pt,a4paper]{refart} \usepackage{german} % other packages you may want \end{verbatim} \subsection{Options} \index{options} The \texttt{refart} class replaces \texttt{article} and \texttt{refrep} replaces \texttt{report}. They support all options of these classes except for the \texttt{twocolumn} option. It supports the additional option \texttt{square} which makes the \cs{textheight} equal to the \cs{textwidth}. Neither \texttt{refart} nor \texttt{refrep} support two column layout, thus the commands \cs{twocolumn} and \cs{onecolumn} must not be used. The index will be set in two column format and you can't change it with the means of this class. \subsection{Layout changes} \subsubsection{Page design} \index{page design, horizontal}\marginlabel{Horizontal:} In this design the usable area for text (\cs{fullwidth}) is calculated as the paper width minus 2~\cs{papermarginwidth}. The default value for \cs{papermarginwidth}\index{papermarginwidth} is 1~Inch. The option \texttt{smallborder} reduces \cs{papermarginwidth} to 0.25~Inch. This is more suitable for documents viewed on screen, especially when combined with the \texttt{a5paper} and \texttt{landscape} options. Only a fraction of this width is used for the running text (\cs{textwidth}), the remaining part forms a wide left margin (\cs{leftmarginwidth}) which is used for headings and margin notes. The \cs{textwidth} is 70~\% of the \cs{fullwidth} by default, but this can be changed with the \cs{settextfraction} command\index{settextfraction} which accepts arguments between 0 and 1. \index{page design, vertical}\marginlabel{Vertical:} The text height is calculated as the paper height minus 2~\cs{papermarginwidth}. The \texttt{topmargin} is modified by some pagestyles. (see \ref{pagestyle}). The pages are always set with a ragged bottom. \subsubsection{Section headings} The headings for \cs{section}, \cs{subsection}, and \cs{subsubsection} extend into the left margin, thus using the full width of the page. They are not justified and hyphenation is discouraged. A small space is kept free above and below the heading. Headings for \cs{section} and \cs{subsection} are set in a bold font. The \texttt{refrep} class defines a different layout for the \cs{chapter} command: It always starts a new page and prints the chapter headings in a large bold font with a thick line above and below. This heading uses the full width of the page. A similar heading is created by the \cs{part} commands which is available in both classes. It uses a roman part number instead of the arabic section number. The \cs{maketitle} commands sets the title of the document in the same layout when no special title page is requested. (This is the default for \texttt{refart}. To suppress the title page in a \texttt{refrep} document, you can use the \texttt{notitlepage} option.) The name of the author and the date is printed in italic flush right below the document title. \subsubsection{Paragraphs} Paragraphs are separated by a vertical space (\cs{parskip}) of half a line (\verb|0.5\baselineskip|) plus a stretchable length of 2~pt. Paragraphs are not indented. The vertical spacing inside, above and below a list environment is the same as in the running text. \subsection{Footnotes}\index{footnote} The footnote layout consists of a small margin (1em) which contains the footnote symbol. A small space is set between the symbol and the footnote text. The paragraphs of the footnote are not indented. There is currently no space between two footnotes, I'm not sure it this will stay this way. The footnote symbol is set as a superscript. This may change in later versions. I'm relying on user feedback to finally solve this. \subsubsection{Description environment} \index{description environment} The \texttt{description} environment will use the whole left margin for the description label. \seealso{Section \ref{layout}} You will find examples in the section~\ref{layout}. \subsubsection{Positioning of margin notes} Margin notes (\cs{marginpar}) are always put into the left margin. They use the whole width of the margin. The minimum space between two margin notes is set to 0 to prevent them from being shifted around when many margin notes are used. \subsubsection{Headers and Footers} \label{pagestyle} \index{pagestyle} The page style \texttt{plain} puts the page number into the footer in the right corner. When the option \texttt{twoside} is active, the page number of left pages is put into the left corner. \index{headings} \index{myheadings} The pagestyles \texttt{headings} and \texttt{myheadings} create a header which spans the whole width of the page. The headings contain the running head (\cs{section} and \cs{subsection} in \texttt{refart} and \cs{chapter} and \cs{section} in \texttt{refrep}) when \texttt{headings} is used or a fixed text that can defined with the \cs{markboth} command when \texttt{myheadings} is used. The heading will be set in a slanted font and separated from the body by a thin line. \index{footings} \index{myfootings} In addition to the standard classes, \texttt{refman} supports a style for footers, which is used in this documentation. The information is exactly the same as in the headings but now printed in the footer with a thin line above. To use a user-defined string you can say: \begin{verbatim} \pagestyle{myfootings} % or myheadings \markboth{left title}{right title} \end{verbatim} The \texttt{heading} and \texttt{myheading} commands increase the top margin by one line while the \texttt{footings} and \texttt{myfootings} commands decrease the top margin by one line. The page styles \texttt{empty} and \texttt{plain} leave the top margin unchanged. You should not combine headings and footings in one document. User feedback has shown that it is not a good idea to combine \texttt{plain} and \texttt{(my)heading} either. Therefore I changed the layout of the \cs{chapter} page to \texttt{empty}. Maybe it is necessary to define a \texttt{hplain} and \texttt{fplain} pagestyle or to define some magic to use the correct definition of \texttt{plain}. Feedback is welcome. \subsection{Additional commands} \subsubsection{Marginlabel} \index{marginlabel} The command \verb|\marginlabel{xxx}| prints the text \texttt{xxx} right justified into the left margin. Please note that a \cs{marginpar} will print it left justified. \marginlabel{Example:} The word ``Example'' in the left margin is printed with the command \verb|\marginlabel{Example:}| \subsubsection{Attention} \index{attention}\index{attentionsymbol}\index{manfnt} The command \cs{attention} puts an exclamation mark with an arrow pointing to the text into the left margin.\attention{} This is an example for \cs{attention}. \renewcommand{\attentionsymbol}{\texttt{:-)}} \attention Since version 2.0c you can change the symbol used for the \cs{attention} command using a \verb|\renewcommand{\attentionsymbol}{\texttt\{:-)\}}| command. To get the default back use \verb|\renewcommand{\attentionsymbol}| \verb|{\large \bfseries ! $\rightarrow$}| \renewcommand{\attentionsymbol}{\large \bfseries ! $\rightarrow$} Since version 2.0c \cs{attention} takes an optional argument to define the symbol used in the margin. Thus you can change the symbol once, without having to restore it later. Do not abuse this feature\attention[\texttt{:-(}], it is primarily meant as an support for the \texttt{manfnt} package which enables you to use the ``dangerous bend'' and ``double dangerous bend'' signs. The \texttt{manfnt} package is no longer enclosed with Refman, it has grown and is now a package of its own. \subsubsection{Seealso} \index{seealso} The command \verb|\seealso{n}| prints an arrow and its argument into the left margin. You will find examples for this in the left margin and in \seealso{Chapter 1} chapter~1. \subsubsection{Maxipage environment} \index{maxipage} The \texttt{maxipage} environment is a special kind of \texttt{minipage} which extends over the full width of the page. It can be used for long formulas or \texttt{tabular} environments. You may use \texttt{maxipage} environments inside floats. You cannot use margin notes inside a \texttt{maxipage} and no page break will occur while in a \texttt{maxipage}. A \texttt{maxipage} is always a paragraph of its own with a thick line above and below. You can disable these lines with the \cs{maxipagerulefalse}\index{maxipagerule} command. They are on by default. The following paragraph is an example for a \texttt{maxipage}: \nopagebreak \begin{maxipage} This very long line is an example for a \texttt{maxipage}. It extends over the full width of the page, including the left margin. \end{maxipage}\nopagebreak This is normal text after the \texttt{maxipage}. \subsubsection{Fullpage environment} \label{fullpage} \index{fullpage} The \texttt{fullpage} environment consists of one or more pages where the text extends over the full width of the page. You cannot use margin notes inside a \texttt{fullpage} environment. A \texttt{fullpage} will always start and end on a page of its own. It may be used for large tables, program listings or anything that does not fit into the normal layout. \seealso{Page \pageref{bild}} Page~\pageref{bild} is an example for a \texttt{fullpage}. \subsubsection{Noparskip} The \cs{noparskip} removes the vertical space between two paragraphs. It is similar to the \cs{noindent} command that removes the indent of the first line of a paragraph. \subsubsection{Setleftmarginwidth} \index{setleftmarginwidth} The \cs{setleftmarginwidth} command is no longer supported. You can achieve similar results by using the \cs{settextfraction} command. \subsubsection{Descriptioncolon} \index{descriptioncolon} By default a colon is printed after the description label. The command \cs{description\-colonfalse} disables the colon, the \cs{description\-colontrue} re-enables it. \subsubsection{Descriptionleft} \index{descriptionleft} The \cs{descriptionlefttrue} command sets the description label left justified into the margin. The default is right justified which will be achieved with \cs{descriptionleftfalse} \subsubsection{Maxipagerule} \index{maxipagerule} You can disable the rules before and after a \texttt{maxipage} with the \cs{maxipage\-rulefalse} command and re-enable them with the \cs{maxipageruletrue} command. The default is on. You should not mix \texttt{maxipage}s with and without rules in one document. \subsubsection{Condbreak} \index{condbreak} The command \verb|\condbreak{2cm}| ensures, that the next 2~cm are either completely on this page or completely on the next. No page break will appear in the next 2~cm. This is really a hack to achieve what the \cs{samepage} command often fails to do. \subsubsection{Example} \index{example} The \texttt{example} environment acts like a \texttt{verse} environment but uses a \texttt{tt} font. \subsubsection{Pageperchapter} \index{pageperchapter} The command \cs{pageperchapter} creates page number that start with 1 for every new chapter. This may be useful for larger manuals. Since it works with chapters it is only available in the \texttt{refrep} class. \subsubsection{Smallborder} \index{smallborder} The normal border around the page is 1~Inch. That is fine for a printed document, but wastes a lot of space when a document is meant for reading on screen. The option \texttt{smallborder} reduces the margin to 0.25~Inch. You can redefine the border with \cs{setlength}\cs{papermarginwidth} \verb|{0.25in}|. Call \verb|\setpagefraction{0.7}| afterwards to recalculate the page layout. \subsubsection{Dvips} \index{dvips} The option \texttt{dvips} tells DVIPS about the current page size. \subsubsection{Pdftex} \index{pdftex} The option \texttt{pdftex} tells PDF\TeX about the current page size. \subsubsection{Pagesize} \index{pagesize} \texttt{pagesize} chooses the correct \cs{special}-command to tell the DVI-driver about the paper size. It works with DVIPS and DVIPDFMX for DVI output and PDF\TeX\ for PDF output. \subsubsection{Ifpdfoutput} \index{ifpdfoutput} You can use \verb|\ifpdfoutput{pdftext}{dvitext}| to write different text depending on the output format. This command was necessary to implement the \texttt{pagesize} option and is available for the user as well. The last four commands have been taken from KOMA-Script, thanks Markus. %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% \endinput